Alfawise U30 2.8 inch Touch Screen DIY Desktop 3D Printer

BUY AT GEARBEST

Description:
Alfawise U30 is an incredible 3D printer designed for professionals and amateurs alike. It trains hands-on ability, and only 1 hour is required to finish the assembly. It boasts high cost-performance ratio - any DIY enthusiast will not be unable to resist. U30 has a large build volume - 220 x 220 x 250mm for most challenges. More importantly, printing with Alfawise U30 is hassle-free because the two resume functions prevent any imperfection and failure due to power outage and filament run-out. Control the process and set parameters on the touchscreen. Enjoy easier and more successful 3D printing!

  • Description
  • Specification
  • Video
  • Downloads
  • FAQ
  • Learn More

Main Features:
220 x 220 x 250mm maximum build volume to print exciting models
Precision printing with standard 0.4mm diameter nozzle, accurate alignment, and up to 120mm/s speed
● More successful in 3D printing with filament run-out protectionandpower outage protection
2.8'' full color touchscreen for more intuitive control
Great DIY project for any beginners to train hands-on ability, only 1 hour needed
Reinforced aluminum alloy construction, durable, in classical black and red colors
Powerful heat bed using safety voltage for fast heating. With heat-resistant heat bed sticker, easier to use and clean
● 100 Deg.C max. heat bed temperature, 250 Deg.C max. nozzle temperature for various filaments, such as PLA, ABS, PVA, PP, TPU, wood filled, etc.


Tip: the power outage recovery functions well when you print more than 0.5mm in height. If the height is less than 0.5mm, it is recommended to print again.

General

Brand: Alfawise
Type: DIY
Model: U30
Engraving Area: 220 x 220 x 250mm
Frame material: Aluminum Alloy
Nozzle quantity: Single
Nozzle diameter: 0.4mm
Nozzle temperature: Room temperature to 250 degree
Layer thickness: 0.1-0.4mm
Memory card offline print: TF card
LCD Screen: Yes
Print speed: 120mm/s (max.), 30 - 70mm/s ( recommended )
Platform temperature: Room temperature to 100 degree
Supporting material: ABS,PLA,Wood Filled
Material diameter: 1.75mm
File format: G-code,OBJ,STL
XY-axis positioning accuracy: 0.0125mm
Z-axis positioning accuracy: 0.0025mm
Voltage: 24V
Host computer software: Cura,Repetier-Host,Simplify3D
Packing Type: unassembled packing
System support: Windows / Mac / Linux
Connector Type: TF card,USB

Alfawise U30. Aufbau und der erster Druck.

Alfawise U30, une imprimante 3D à 150€ que je vous conseille !

Alfawise U30 3D Printer

Лучший 3D принтер для каждого бюджета

Unboxing stampante 3D Alfawise U30 in anteprima mondiale

Alfawise U30 Guide

How to update the firmware of Alfawise U30 DIY 3D Printer?

1. Copy firmware to the SD card;

2. Then restart the machine and wait for the machine progress bar to complete before the firmware is refreshed.

3. Then the user needs to delete firmware in the SD card to be used normally, otherwise the firmware will be refreshed every time the printer is turned on.

Why not extruding at start of print?

1. Extruder was not primed before beginning the print;

2. Nozzle starts too close to the bed;

3. The filament has stripped against the drive gear;

4. The extruder is clogged.

When the machine returns the filament, it can't be returned. What should I do when stuck in the pneumatic joint?

1. Before returning the material, please heat the nozzle first, and then withdraw the consumables as soon as possible. If you can't pump it, you can re-feed the material with the advanced material, and melt the extruded block formed at the end of the consumable in the nozzle.

2. When withdrawing the consumables, before the end of the consumables reaches the pneumatic joint, we will usually pull the Teflon directly from the Teflon and cut the end of the consumables.

3. Because the end of the consumables in the nozzle will be deformed by heat, if the end deformed consumables are directly pulled out, it may be stuck to the pneumatic joint or the limit switch for damage detection. (The limit switch for the broken material detection is single Towards).

Why not extruding enough plastic?

1. Incorrect filament diameter;

2. Increase the extrusion multiplier.

Why the 3D printer always overheating?

1. Insufficient cooling;

2. Printing at too high of a temperature;

3. Printing too fast;

4. Try printing multiple parts at once.

What if the filament does not discharge from the machine?

1. After the machine nozzle is heated, the consumables are normally fed into the feeding mechanism by hand, and then passed through the Teflon tube to enter the nozzle.

2. When it is found that the gear of the feeding mechanism emits a "beep" sound, it can first check whether the consumables are wound, causing the extrusion mechanism to pull the material.

3 If this is not the reason, raise the machine nozzle and use the 0.4mm needle in the toolbox to insert it from below the copper nozzle and rotate while inserting.

4. Under normal circumstances, this needle can be used to open the copper nozzle, so that the feed is smooth. The reason for this blocking is generally that there are impurities in the consumables, which leads to plugging.

What should I do if I cannot resume printing after power shutdown?

If the power is suddenly turned off when the part is first printed, the machine will not save the print data. Unless the height of the print exceeds 0.5mm, the power failure will be supported. If the height is less than 0.5mm, it is recommended to reprint directly.

Customer Reviews

Based on 9 reviews Write a review

QUESTIONS & ANSWERS

Ask a Question
  • Hi, What is the right distance between the heatsink and the heating block to reassembling the printing head ? David

    The distance between the heatsink and the heating block to reassembling the printing head is 4.7mm.

  • Is it possible to use the newest version of cura ? Because the one on the card is an really old one

    Yes, it is possible.

  • How do I set up the Alfawise U30 printer in CURA 3.6.0?

    Please refer to this link: http://www.gw-ec.com/upload/uedtor/uploadfile/20190128/1548638885249631.pdf

  • Where I can get the CURA Basicparamters for this Printer ??

    Please refer to this link: http://www.gw-ec.com/upload/uedtor/uploadfile/20190128/1548638885249631.pdf

  • When u30 will be available in European warehouses?

    In this case, you can contact the customer service of gearbest.com, our authorized distributor.

  • Hi Is it possible to print on U30 from the computer and not from TF card? If yes, thru what software?

    Yes, there are corresponding software and instructions in the shipped TF card.

  • Do you ship in Cameroon?

    Yes, we can ship it to Cameroon.

  • What is the maximum temperature you can get on the extruder 3D printer Alfawise U10, U20, U30.

    U10 maximum temperature:260℃ ; U20 maximum temperature:250℃ ;  U30 maximum temperature:250℃

  • I accidently wiped the TF card that came with my printer. Would I be able to recieve a copy of the cura profile. I can't seem to get the printer working with my own profile I made.

    Please transfer the U30.ini onto your TF card. Click here to download: https://bit.ly/2s1dHU1  ; If your the data on TF card has been deleted, please click here to download the file: https://bit.ly/2SgMp7j

  • Gearbest does not ship to India. Any other option?

    Gearbest supports shipping to India, as demonstrated on the screenshot

  • Do you ship to India?

    Yes,we can ship the 3D printer to India.  

  • 8 bits or 32 bits processor?

     32 bits processor

  • Do you have Europ distrbution?

    Yes,we can send the item from our warehouse in Europe.

  • Hi, where ca i find the U30 printer profile for Cura 3.6.0 ? ont the SD card you only have a profile for cura 15.04.3 ;(

    If your the data on TF card has been deleted, please click here to download the file: https://bit.ly/2GF4BpS

  • Heartbeat does not ship to India. Do you sell on Banggood or AliExpress?

    No, we don't sell on Banggood or AliExpress. Gearbest is our only authorized distribution channel.

  • Hi, where ca i find the U30 printer profile for Cura ?

    The U30 printer profile is in the TF card of the machine.